Skip to main content

FLUSHING FLUID - THERMINOL FF

Flushing Fluid

Therminol FF is the first synthetic flushing fluid for liquid phase heat transfer systems. Deposits from oxidized, thermally degraded or contaminated fluid can foul interior surfaces, making it necessary to clean the system prior to charging with new fluid.

Therminol FF is a key component of a low cost alternative to chemically cleaning a heat transfer system containing severely degraded or contaminated organic heat transfer fluid. Deposits from oxidized, thermally degraded or contaminated fluid can foul interior surfaces, making it necessary to clean the system prior to charging with new fluid.

Therminol FF is a synthetic hydrocarbon with a high flash point and initial boiling point, making it much safer to use.

Due to its high boiling point Therminol FF can be safely heated up to 1600 C while circulating in the system to increase its strong solvent action and overall effectiveness as a cleaning fluid.

Small amounts of Therminol FF left in the system will be miscible and compatible with most organic heat transfer fluids. This compatibility factor means less downtime. Water based cleaning solutions add costly drying time to a clean-out procedure, creating additional chance for contamination. Therminol FF eliminates drying, the significantly reducing the length of the procedure.

Performance Benefits

  • Fast and Easy–Using Therminol FF to flush your fouled system is faster than chemical cleaning and requires less downtime. This is because you simply drain the old fluid, add Therminol FF and circulate, drain and refill with your new heat transfer fluid.

  • Less Costly–Therminol FF is a key component of a low-cost alternative to chemically cleaning a heat transfer system containing severely degraded or contaminated organic heat transfer fluid.

  • Compatible With New Fluid–Therminol FF is compatible and miscible with most organic heat transfer fluids, which means less downtime is required for system cleaning.

  • Safety–Therminol FF is a synthetic hydrocarbon with a high flash point and high initial boiling point, making it much safer to use than other cleaning solvents.

  • Effective–To help you decide on the correct clean-out procedure, your Therminol specialist can help you develop the necessary parameters required to maximize the effectiveness of the flushing process.


Applications

  • Specialty chemicals
  • System flushing fluid

Key attributes

  • Compatible with New Fluid
  • Effective
  • Fast and Easy
  • Less Costly
  • Safety


Labels:

Comments

Post a Comment

Popular posts from this blog

Industrial Combustion Burner: Basics of "Industrial Burner"

Industrial Engineering involves creating products that maximize function, value, and appearance for professional manufacturers and consumers. Gas burner, Oil burner, or Coal burner is relate to a mechanical device that burns a gas or liquid fuel in a controlled manner. An oil burner (engine) is a steam engine that uses oil as its fuel. Gas burner , a piece of metal fitted to the end of a gas pipe, with one or more small holes so arranged as to spread out the flame. An oil burner is a part that join to an oil furnace, water heater, or boiler. A Low NOx burner is a type of burner that is typically used in utility boilers to produce steam and electricity. The burner is simply a hollow metal disk with holes punctured through its perimeter. And a gas pilot light or electric pilot sits to one side of the burner and sends a small flame or spark to ignite the oxygen-gas mixture as it flows through the holes in the burner. Industrial Gas burner is a device to generate a flame to heat up produ
3 comments
Read more

HIGH PRESSURE GAS TRAIN Components | Industrial Products

A Typical Fuel Train or High Pressure Gas Train has several components, each with a specific purpose which is briefly explained below: Manual shut-off valve (MSOV) – the purpose of this valve is to shut off the fuel  supply so that maintenance or replacement of the fuel train may be done. Gas pressure regulator (PRV) – its purpose is to maintain the fuel at a constant  pressure as recommended by the burner manufacturer. Gas Filter – the function is to prevent foreign particle and extraneous impurities  entering Gas Pressure Regulator. Low pressure gas switch – senses a low pressure in the range where the burner  cannot properly operate. This switch must be equipped with safety lock-out requiring manual reset. This tells the operator to check the gas pressure, since the burner will not try to restart until the switch is reset. Safety shut-off valve (SSOV) – the first of two valves in series that automatically  opens and shuts off the fuel supply to the burner. On burners above 1200
1 comment
Read more

USE OF THERMIC FLUID HEATERS, ENSURING RELIABILITY AND LONGER LIFE FOR THERMIC FLUID

Thermic Fluid Heater is most popular in almost every industries and it is being used for various heating applications due to unique advantage over other heating systems like steam heating, electrical heating, direct firing, air heating etc., because of the following exceptional advantages:- Very low working pressure and safe from explosion hazards. Heat transfer medium or working fluid remains in liquid phase throughout and higher overall heat transfer. Greater efficiency of heat utilization , superior fuel-saving possibility, and better return on investment for the industry. No botheration continuous water treatment for feed water in case of steam boiler. No problem of scale deposition on heating surface. New generation thermic fluids with excellent properties are available in the market Better heat transfer coefficient, higher thermal stability, and long-life cycle Exemption from Indian Boiler Regulations Act and related formalities Thus, many unique advantages when selecting the the
Post a Comment
Read more